Steel frame with precision laser cutouts and powder coating, steel shafts with zinc plating, hard anodized black aluminum trigger and thumb button.  Upgraded Delrin gears, mil-spec potentiometers, precision springs and upgraded handles.  OEM flange bearings and OEM retaining rings.  All parts meet or exceed original Atari spec.  All components are 100% interchangeable with original yoke controller. Note: Does NOT come with artwork.

Atari Part # A040233-01

Complete set of handle components (both right and left sides).  Cast 7075 Aluminum Alloy, powder coated black.  Exceeds original Atari spec.  100% Compatible with original Atari controllers as well as reproduction controller.

Custom made USB interface adapter for yoke controller.  Plug and Play connectivity, simply plug yoke controller into interface board and plug USB cable into M.A.M.E. computer.  Features support for dual axis (pitch-up/down and roll-right/left) analog controls and four momentary switches (right/left thumb buttons and right/left trigger buttons).  The only complete plug and play USB solution for OEM and reproduction yoke controllers.  Includes 3ft USB cable.

All cold rolled steel construction, precision laser cut, precision formed, TIG welded, powder coated black.  Fasteners are press-fit by 20ton press.  Exceeds original Atari HRP&O steel specification.  (Picture to left is pre-production model and does not depict final zinc plated part.)

Part #:  A040236-01

All cold rolled steel construction, precision machined and laser cut, precision formed, TIG welded, powder coated black.  Exceeds original Atari HRP&O steel specification.  (Picture to left is pre-production model and does not depict final powder coated part.)

Part #:  A040247-01

All cold rolled steel construction, precision laser cut, precision formed, powder coated black.  Exceeds original Atari HRP&O steel specification.  (Picture to left is pre-production model and does not depict final powder coated part.)

Part #:  A040251-01

Black 75D Cast Polyurethane.  The material choice has very good wear properties and it looks good.  These parts far exceed original Atari specification.  Price is for two triggers.

Part #:  040303-01

Shaft mounted to handle assembly frame, through each side, connected to handles for up/down movement.  Made from hardened steel, ground to spec, machined, and zinc plated gold.  Meets original Atari specifications.

Part #:  040242-01

Attaches to steering assembly frame and handle assembly frame.  Made from hard neoprene rubber affixed to a steel base, this part is within original Atari spec and engineered to be serviced easily in the future.  Price is for four rubber bumpers.

Part #: 040240-01

Attaches to steering assembly frame and handle assembly frame.  Made from powdered bronze, cast to spec and pre-lubed.  Must be press-fit in frame.  Price is for four flange bearings.

Part #:  040243-01

Reverse screened onto .010” polycarbonate, textured matte finish with 3M adhesive backing.  Made from original Atari films, colored matched to Atari spec.  Die cut from original Atari specification as well.  This is a modern day (superior) equivalent to the OEM decal.  Artwork is completely matched to OEM spec.

Part #:  040382-07, 040381-04, 040532-07, etc

Special 3-conductor control wiring which was custom made for the reproduction Atari flight yoke controller.  It’s an exact match for the OEM wire used by Atari, all the way down to the gauge, color and stand count.  The high strand count makes this wire especially flexible which is ideal for this application.  The wire is perfectly matched to OEM specification so it will work with OEM controllers as well as the reproduction controllers.  Price includes 10ft of wire.

Shaft mounted to rear of handle assembly frame, through steering assembly frame for left/right movement.  Made from hardened steel, ground to spec, machined, and zinc plated gold.  Meets original Atari specifications.

Part #:  040234-01

Gear made from cast Delrin material and hub made from 6061 aluminum.  Mounts to shafts located in steering assembly frame and handle assembly frame and is used for up/down and left/right movement.  Gear formation is to exact Atari specifications, but materials have been upgraded and therefore exceed Atari specs.

Part #:  040235-01

Gear made from cast Delrin material and hub made from 6061 aluminum.  Mounts to potentiometer located in steering assembly frame and controls left/right movement.  Gear formation is to exact Atari specifications, but materials have been upgraded and therefore exceed Atari specs.

Part #:  178101-003

Gear made from cast Delrin material and hub made from 6061 aluminum.  Mounts to potentiometer located in handle assembly frame and controls up/down movement.  Gear formation is to exact Atari specifications, but materials have been upgraded and therefore exceed Atari specs.  Special attention was made to the upgrades of this specific part due to the extremely high failure rate of the OEM counterpart.

Part #:  040249-01

Mounted within handles for game fire control.  Made from 6061 aluminum and hard black anodized for a long-lasting part which far exceeds original Atari specifications.  Price is for two thumb buttons.

Part #:  040096-01

This is a brand new small torsion spring used in the handle assembly frame for tension on up/down movement.  Parts made in-house within spec.  Price is for two small torsion springs.

Part #:  040246-01

This is a brand new large torsion spring used in the steering assembly frame for tension on left/right movement.  Parts made in-house within spec.  Price is for two large torsion springs.

Part #:  040239-01

Mounts inside of handle assembly frame and steering assembly frame for up/down/left/right movement.  An extreme improvement to the original Allen-Bradley potentiometers used by Atari, these are absolutely top notch parts!  Meets or exceeds Military specification MIL-R-94 and has a rotational life of 1,000,000 cycles.  Price is for two pots with mounting nuts.  NOTE:  This part is for use in non-OEM installations which usually require an adaptor board to connect to a personal computer.

Mounts inside of handle assembly frame and steering assembly frame for up/down/left/right movement.  An extreme improvement to the original Allen-Bradley potentiometers used by Atari, these are absolutely top notch parts!  Meets or exceeds Military specification MIL-R-94 and has a rotational life of 1,000,000 cycles.  The smooth response and tracking from this part is simply amazing!  Replace those worn pots!  Price is for two pots with mounting nuts

Subminiature snap-action switches used in handles for thumb buttons and triggers.  These are OEM Cherry brand replacement parts.  This is an exact part which will work with the OEM controller and the reproduction controller.  Price is for a total of four switches.

Part #:  160026-001

This rebuild kit includes all of the following items:  (4) Rubber Bumpers, (2) Thumb Buttons, (4) Small Compression Springs, (4) Snap-Action Switches, (2) 60-Tooth Gears, (1) 28-Tooth Gear, (1) 14-Tooth Gear, (2) “Extra Life” Precision 5K Potentiometers, (1) Spacer Bearing, (1) Tube Nyogel 779ZC,  (2) Large Torsion Springs, (2) Small Torsion Springs, (4) Flange Bearings, (1) Steering Shaft, (1) Handle Shaft, (1) Anchor Pin, (1) Anchor Nut, (1) Spring Pin.

Special silica-thickened, light viscosity, synthetic hydrocarbon grease intended for mechanical components that require a light level of damping (noise/chatter reduction).  This is the exact grease called out in Atari specifications with an added moly lubricant for better aluminum on aluminum lubrication.  It also has an added benefit of quieting down plastic gears!  Comes in a 10 gram tube - enough for several applications.

Machined Delrin.  Fits between handle assembly frame and steering assembly frame.  Upgraded material exceeds original Atari spec.

Part #:  040241-01

Attaches to handle shaft to retain torsion springs.  Made from hardened steel and zinc plated gold, this part exceeds original Atari specifications.

Part #:  040244-01

This rebuild kit includes all of the following items:  (4) Rubber Bumpers, (2) Thumb Buttons, (4) Small Compression Springs, (4) Snap-Action Switches, (2) 60-Tooth Gears (1) 28-Tooth Gear, (1) 14-Tooth Gear, (2) “Extra Life” Precision 5K Potentiometers, (1) Spacer Bearing, (1) Tube Nyogel 779ZC,  (2) Large Torsion Springs, (2) Small Torsion Springs.

This rebuild kit includes all of the following items:  (4) Rubber Bumpers, (2) Thumb Buttons, (4) Small Compression Springs, (4) Snap-Action Switches, (2) 60-Tooth Gear, (1) 28-Tooth Gear, (1) 14-Tooth Gear, (2) “Extra Life” Precision 5K Potentiometers, (1) Spacer Bearing, (1) Tube Nyogel 779ZC.

Attaches to steering shaft to retain torsion springs.  Made from hardened steel and zinc plated gold, this part exceeds original Atari specifications.

Part #:  040234-01

Attaches to steering shaft to retain torsion springs.  Made from hardened steel and zinc plated gold, this part exceeds original Atari specifications.

Part #:  040237-01

This is a brand new compression spring used in the handles for tension on the thumb buttons and trigger buttons.  Parts made in-house within spec.  Price is for four compression springs.

Part #:  040252-01